WA2WA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA2WA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Charge*	Rtime*	Input*	Load*
1785070502	97 %	11628 s	124 V	2 %
1785069902	97 %	13993 s	124 V	1 %
1785069622	97 %	13993 s	124 V	1 %
1785069002	97 %	13993 s	124 V	1 %
1785068402	97 %	13534 s	123 V	1 %
1785068102	97 %	13993 s	123 V	1 %
1785067803	97 %	13993 s	123 V	1 %
1785067202	97 %	13993 s	123 V	1 %
1785066602	97 %	14484 s	123 V	1 %
1785066302	97 %	13993 s	123 V	1 %
1785066002	97 %	13993 s	123 V	1 %
1785065435	97 %	13993 s	123 V	1 %
1785065102	96 %	13993 s	123 V	1 %
1785064802	97 %	14484 s	123 V	1 %
1785064502	97 %	13993 s	123 V	1 %
1785064202	97 %	13993 s	123 V	1 %
1785063603	97 %	13993 s	123 V	1 %
1785063002	97 %	13993 s	123 V	1 %
1785062702	97 %	13993 s	123 V	1 %
1785062402	97 %	13534 s	123 V	1 %
1785062102	97 %	13993 s	123 V	1 %
1785061803	97 %	13993 s	123 V	1 %
1785061502	97 %	13993 s	123 V	1 %
1785061202	97 %	13993 s	123 V	1 %
1785060902	97 %	13993 s	123 V	1 %

*Used Equation Coefficients:

Charge: 0, 1, 0

Rtime: 0, 1, 0

Input: 0, 1, 0

Status: 0, 1, 0

Load: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)