DG1FBP-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG1FBP-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1787585297	21.1 C deg	58.4 %	0 C deg
1787583467	21.1 C deg	58.3 %	0 C deg
1787581637	21.3 C deg	58.2 %	0 C deg
1787579807	20.9 C deg	59.8 %	0 C deg
1787577977	20.9 C deg	59.7 %	0 C deg
1787576147	21.1 C deg	59.2 %	0 C deg
1787574317	21.1 C deg	59.2 %	0 C deg
1787572487	21.2 C deg	58.8 %	0 C deg
1787570657	21.2 C deg	58.3 %	0 C deg
1787568827	21.2 C deg	58.1 %	0 C deg
1787566997	21.1 C deg	59 %	0 C deg
1787565167	20.8 C deg	59.2 %	0 C deg
1787563337	20.8 C deg	58.8 %	0 C deg
1787561507	20.8 C deg	58.9 %	0 C deg
1787559677	20.8 C deg	58.8 %	0 C deg
1787557846	20.7 C deg	58.8 %	0 C deg
1787556017	20.7 C deg	59.6 %	0 C deg
1787554186	20.7 C deg	59.7 %	0 C deg
1787552356	20.7 C deg	60.3 %	0 C deg
1787550526	20.6 C deg	60.3 %	0 C deg
1787548696	20.4 C deg	61.5 %	0 C deg
1787520229	22.8 C deg	57.8 %	0 C deg
1787518399	23.6 C deg	56.5 %	0 C deg
1787516569	23.6 C deg	56.4 %	0 C deg
1787514739	23.3 C deg	57.1 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)