DL1TK-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL1TK-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1776703711	23.7 deg C	29.3 %	1016.2 hPa
1776702812	23.4 deg C	28.3 %	1017.3 hPa
1776701911	22.9 deg C	26 %	1017.2 hPa
1776701011	22.9 deg C	23.6 %	1015.3 hPa
1776700111	23 deg C	22.4 %	1014.7 hPa
1776699211	23.3 deg C	21.5 %	1014.6 hPa
1776698311	23.4 deg C	23.4 %	1017.6 hPa
1776697411	23.3 deg C	23.1 %	1016.7 hPa
1776696511	23.4 deg C	24.4 %	1016.3 hPa
1776695610	23.4 deg C	24.3 %	1016 hPa
1776694710	23.6 deg C	24.2 %	1018.3 hPa
1776693810	23.8 deg C	24.7 %	1016.9 hPa
1776692910	24 deg C	24.4 %	1015.8 hPa
1776692010	24.3 deg C	29 %	1015.8 hPa
1776691110	24.1 deg C	26.4 %	1015.5 hPa
1776690210	24.8 deg C	26.1 %	1017.6 hPa
1776689310	25.1 deg C	31.4 %	1020.3 hPa
1776688410	25.1 deg C	31.9 %	1018.9 hPa
1776687510	25 deg C	30.8 %	1016.8 hPa
1776686610	25 deg C	32.6 %	1018.4 hPa
1776685709	24.7 deg C	32.4 %	1017.8 hPa
1776684809	24.5 deg C	29 %	1016.8 hPa
1776683909	24.2 deg C	31.5 %	1018 hPa
1776683009	24.1 deg C	32 %	1015.9 hPa
1776682109	24.1 deg C	32.7 %	1015.2 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)