M7AQH-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M7AQH-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	BARO*
1765564374	24.6 C	58.41 %	1628 hPa
1765563774	24.84 C	58.12 %	1628 hPa
1765563174	25.11 C	58.41 %	1628 hPa
1765563161	25.11 C	58.41 %	1628 hPa
1765562611	24.81 C	58.4 %	1628 hPa
1765562011	24.81 C	58.53 %	1628 hPa
1765561413	24.82 C	58.57 %	1628 hPa
1765560811	24.88 C	58.57 %	1628 hPa
1765559611	25.12 C	58.56 %	1628 hPa
1765559011	25.12 C	58.62 %	1628 hPa
1765558411	25.07 C	58.74 %	1628 hPa
1765557811	25 C	58.88 %	1628 hPa
1765557211	24.87 C	59.07 %	1628 hPa
1765556611	24.75 C	58.37 %	1628 hPa
1765556011	24.6 C	59.36 %	1628 hPa
1765554811	24.42 C	59.66 %	1628 hPa
1765554213	24.42 C	59.66 %	1628 hPa
1765553613	24.37 C	59.83 %	1628 hPa
1765553011	24.32 C	60 %	1628 hPa
1765552411	24.26 C	60.05 %	1628 hPa
1765551811	24.2 C	60.07 %	1628 hPa
1765551211	24.21 C	60.07 %	1628 hPa
1765550611	24.22 C	60.14 %	1628 hPa
1765550013	24.14 C	60.29 %	1628 hPa
1765549411	24.1 C	60.32 %	1628 hPa

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.01, 0

BARO: 0, 0.1, 800

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)