M7AQH-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M7AQH-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Celsius*	Rel_Hum*	Atm_Press*
1789969498	17.9 C	57.61 %	1031.75 hPa
1789968452	15.5 C	59.04 %	1031.13 hPa
1789967219	11.7 C	62.59 %	1033.38 hPa
1789966473	8.4 C	59.12 %	1033.38 hPa
1789921126	22.1 C	45.62 %	1033.25 hPa
1789919134	23.7 C	42.71 %	1033 hPa
1789918414	25.1 C	41.01 %	1027.25 hPa
1789918299	25 C	40.89 %	1028 hPa
1789917359	24.8 C	40.91 %	1025.75 hPa
1789916943	25.3 C	40.48 %	1024 hPa
1789916672	26.1 C	39.63 %	1026.5 hPa
1789916286	26.1 C	38.92 %	1024 hPa
1789915965	26.5 C	38.56 %	1025.13 hPa
1789915656	26.5 C	38.18 %	1025.88 hPa
1789915388	27 C	37.86 %	1025.38 hPa
1789914932	30.9 C	34.26 %	1026.5 hPa
1789914574	35 C	30.65 %	1026.75 hPa
1789914095	40.8 C	32.84 %	1023.13 hPa
1789841695	22.7 C	52.88 %	1013.5 hPa
1789841113	21.9 C	52.59 %	1013.75 hPa
1789833318	27.3 C	44.17 %	1012.75 hPa
1789832005	31.4 C	39.59 %	1012 hPa
1789831653	34.3 C	41.79 %	1014 hPa
1789758335	18.1 C	67.75 %	1008.88 hPa
1789756946	16.4 C	65.17 %	1003.25 hPa

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)