SP9DAT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9DAT-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*	V_Bat*
1761491389	855 Count	414 Count	358 Count	3.55 VDC
1761490490	854 Count	414 Count	358 Count	3.55 VDC
1761489588	853 Count	414 Count	358 Count	3.55 VDC
1761488687	852 Count	414 Count	358 Count	3.55 VDC
1761487786	850 Count	412 Count	357 Count	3.55 VDC
1761485984	847 Count	411 Count	356 Count	3.55 VDC
1761485084	846 Count	411 Count	356 Count	3.55 VDC
1761484183	845 Count	411 Count	356 Count	3.55 VDC
1761483282	843 Count	410 Count	355 Count	3.55 VDC
1761482381	841 Count	409 Count	354 Count	3.55 VDC
1761481480	840 Count	409 Count	354 Count	3.55 VDC
1761480579	838 Count	408 Count	353 Count	3.55 VDC
1761479679	836 Count	407 Count	352 Count	3.55 VDC
1761478778	835 Count	407 Count	352 Count	3.55 VDC
1761477877	833 Count	405 Count	351 Count	3.55 VDC
1761476976	832 Count	405 Count	351 Count	3.55 VDC
1761476075	831 Count	405 Count	351 Count	3.55 VDC
1761475175	829 Count	404 Count	350 Count	3.55 VDC
1761473373	826 Count	403 Count	349 Count	3.55 VDC
1761471571	823 Count	402 Count	348 Count	3.55 VDC
1761470671	822 Count	402 Count	348 Count	3.55 VDC
1761469770	821 Count	402 Count	348 Count	3.55 VDC
1761468869	818 Count	400 Count	346 Count	3.56 VDC
1761467968	815 Count	398 Count	344 Count	3.56 VDC
1761467067	814 Count	398 Count	344 Count	3.56 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)