WA7DRE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA7DRE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V-Input*	Rx1h*	Eff1h*
1789968691	14.1 Volt	10 Pkt	66 %
1789966891	14.1 Volt	10 Pkt	54 %
1789965091	14.1 Volt	10 Pkt	65 %
1789963291	14.1 Volt	10 Pkt	64 %
1789961491	14.1 Volt	10 Pkt	72 %
1789959691	14.1 Volt	20 Pkt	80 %
1789957891	14.1 Volt	30 Pkt	81 %
1789956091	14.1 Volt	40 Pkt	66 %
1789954292	14.1 Volt	30 Pkt	51 %
1789952491	14.1 Volt	10 Pkt	51 %
1789950692	14.1 Volt	20 Pkt	69 %
1789948892	14.1 Volt	20 Pkt	72 %
1789947092	14.1 Volt	50 Pkt	77 %
1789945292	14.1 Volt	70 Pkt	85 %
1789943492	14.1 Volt	90 Pkt	93 %
1789941692	14.1 Volt	120 Pkt	91 %
1789939892	14.1 Volt	120 Pkt	95 %
1789938108	14.1 Volt	90 Pkt	90 %
1789936292	14.1 Volt	90 Pkt	81 %
1789934492	14.1 Volt	80 Pkt	81 %
1789932692	14.1 Volt	50 Pkt	76 %
1789930892	14.1 Volt	40 Pkt	62 %
1789929092	14.1 Volt	40 Pkt	53 %
1789927292	14.1 Volt	30 Pkt	57 %
1789925492	14.1 Volt	20 Pkt	67 %

*Used Equation Coefficients:

V-Input: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)