ED1ZAD-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAD-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RX1h*	DG1h*	Eff1h*
1757592840	500 Pkt	90 Pkt	76 Pcnt
1757592541	510 Pkt	110 Pkt	76 Pcnt
1757592540	510 Pkt	110 Pkt	76 Pcnt
1757592240	530 Pkt	110 Pkt	76 Pcnt
1757591941	520 Pkt	110 Pkt	77 Pcnt
1757591940	520 Pkt	110 Pkt	77 Pcnt
1757591639	530 Pkt	120 Pkt	79 Pcnt
1757591340	530 Pkt	120 Pkt	78 Pcnt
1757591339	530 Pkt	120 Pkt	78 Pcnt
1757591039	540 Pkt	120 Pkt	78 Pcnt
1757590739	550 Pkt	130 Pkt	78 Pcnt
1757590738	550 Pkt	130 Pkt	78 Pcnt
1757590438	540 Pkt	120 Pkt	79 Pcnt
1757590139	530 Pkt	120 Pkt	78 Pcnt
1757590138	530 Pkt	120 Pkt	78 Pcnt
1757589838	530 Pkt	110 Pkt	77 Pcnt
1757589539	530 Pkt	100 Pkt	77 Pcnt
1757589537	530 Pkt	100 Pkt	77 Pcnt
1757589237	520 Pkt	100 Pkt	77 Pcnt
1757588937	500 Pkt	80 Pkt	76 Pcnt
1757588937	500 Pkt	80 Pkt	76 Pcnt
1757588636	490 Pkt	80 Pkt	76 Pcnt
1757588337	500 Pkt	80 Pkt	75 Pcnt
1757588336	500 Pkt	80 Pkt	75 Pcnt
1757588036	510 Pkt	70 Pkt	74 Pcnt

*Used Equation Coefficients:

RX1h: 0, 10, 0

DG1h: 0, 10, 0

Eff1h: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)