YO3FVR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FVR-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Tin*
1789954573	12.9 Volt	100 Pcnt	19.5 C
1789953973	12.98 Volt	100 Pcnt	20 C
1789953373	12.98 Volt	100 Pcnt	20 C
1789952773	12.98 Volt	100 Pcnt	20 C
1789952173	12.98 Volt	100 Pcnt	20 C
1789951573	12.98 Volt	100 Pcnt	20 C
1789950973	12.98 Volt	100 Pcnt	20.5 C
1789950373	13.05 Volt	100 Pcnt	20.5 C
1789949773	13.05 Volt	100 Pcnt	20.5 C
1789949173	12.98 Volt	100 Pcnt	20.5 C
1789948573	13.05 Volt	100 Pcnt	21 C
1789947973	13.05 Volt	100 Pcnt	21 C
1789947373	12.98 Volt	100 Pcnt	21 C
1789946773	13.05 Volt	100 Pcnt	21 C
1789946173	13.05 Volt	100 Pcnt	21.5 C
1789945573	12.98 Volt	100 Pcnt	21.5 C
1789944973	13.05 Volt	100 Pcnt	21.5 C
1789944373	13.05 Volt	100 Pcnt	21.5 C
1789943774	13.05 Volt	100 Pcnt	21.5 C
1789943174	13.13 Volt	100 Pcnt	22 C
1789942574	13.13 Volt	100 Pcnt	22 C
1789941974	13.05 Volt	100 Pcnt	22 C
1789941374	13.13 Volt	100 Pcnt	22 C
1789940774	13.13 Volt	100 Pcnt	22.5 C
1789940174	13.05 Volt	100 Pcnt	22.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Vsol: 0, 0.075, 0

Isol: 0, 0.1, 0

Eff1h: 0, 1, 0

Tin: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)