SM0PQB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SM0PQB-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Eff1h*
1784693143	12.23 Volt	36 C	100 %
1784692843	12.23 Volt	36 C	100 %
1784692543	12.23 Volt	36 C	100 %
1784692243	12.23 Volt	36 C	100 %
1784691943	12.23 Volt	36 C	0 %
1784691643	12.23 Volt	36 C	0 %
1784691343	12.23 Volt	36 C	0 %
1784691050	12.23 Volt	36 C	0 %
1784690743	12.23 Volt	36 C	0 %
1784690443	12.23 Volt	36 C	0 %
1784690143	12.23 Volt	36 C	0 %
1784689843	12.23 Volt	36 C	0 %
1784689543	12.3 Volt	36 C	0 %
1784689243	12.3 Volt	36 C	0 %
1784688943	12.23 Volt	36 C	0 %
1784688643	12.23 Volt	36 C	0 %
1784688343	12.23 Volt	36.5 C	0 %
1784688043	12.23 Volt	36 C	0 %
1784687743	12.23 Volt	36.5 C	16 %
1784687443	12.23 Volt	36.5 C	14 %
1784687143	12.23 Volt	36.5 C	17 %
1784686843	12.23 Volt	36.5 C	18 %
1784686543	12.23 Volt	36.5 C	20 %
1784686243	12.23 Volt	36.5 C	16 %
1784685943	12.23 Volt	36.5 C	15 %

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Temp2: 0, 0.5, -64

Rx10m: 0, 1, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)