ON1KDP-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ON1KDP-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1780608090	13.65 Volt	510 Pkt	74 Pcnt
1780607491	13.65 Volt	510 Pkt	75 Pcnt
1780607490	13.65 Volt	510 Pkt	75 Pcnt
1780607190	13.65 Volt	510 Pkt	76 Pcnt
1780606893	13.65 Volt	520 Pkt	76 Pcnt
1780606890	13.65 Volt	520 Pkt	76 Pcnt
1780606294	13.65 Volt	530 Pkt	77 Pcnt
1780606290	13.65 Volt	530 Pkt	77 Pcnt
1780605993	13.65 Volt	540 Pkt	77 Pcnt
1780605690	13.65 Volt	570 Pkt	78 Pcnt
1780605690	13.65 Volt	570 Pkt	78 Pcnt
1780605390	13.65 Volt	570 Pkt	77 Pcnt
1780605100	13.65 Volt	580 Pkt	77 Pcnt
1780605092	13.65 Volt	580 Pkt	77 Pcnt
1780604790	13.65 Volt	600 Pkt	76 Pcnt
1780604490	13.65 Volt	620 Pkt	76 Pcnt
1780604191	13.65 Volt	600 Pkt	75 Pcnt
1780603890	13.65 Volt	620 Pkt	75 Pcnt
1780603890	13.65 Volt	620 Pkt	75 Pcnt
1780603590	13.65 Volt	630 Pkt	76 Pcnt
1780603291	13.65 Volt	640 Pkt	77 Pcnt
1780602990	13.65 Volt	650 Pkt	77 Pcnt
1780602690	13.65 Volt	640 Pkt	76 Pcnt
1780602690	13.65 Volt	640 Pkt	76 Pcnt
1780602090	13.65 Volt	630 Pkt	76 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

T°: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)