DF9EU-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DF9EU-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Press*	Temp.in*	QNH*	Temp.out*
1789945379	1012 hPa	1.4 C deg	1019 hPa	0 C deg
1789943549	1011.8 hPa	1.6 C deg	1018.9 hPa	0 C deg
1789941719	1011.6 hPa	2 C deg	1018.6 hPa	0 C deg
1789939889	1011.5 hPa	2.8 C deg	1018.6 hPa	0 C deg
1789938059	1011.1 hPa	3.8 C deg	1018.1 hPa	0 C deg
1789936229	1011 hPa	5.4 C deg	1017.9 hPa	0 C deg
1789934399	1010.9 hPa	8 C deg	1017.8 hPa	0 C deg
1789932569	1010.5 hPa	11 C deg	1017.3 hPa	0 C deg
1789929030	1009.9 hPa	39.3 C deg	1016.1 hPa	0 C deg
1789928628	1009.7 hPa	38.5 C deg	1020.2 hPa	0 C deg
1789926827	1009.1 hPa	37.5 C deg	1019.7 hPa	0 C deg
1789924997	1008.8 hPa	35.7 C deg	1019.4 hPa	0 C deg
1789923167	1008.4 hPa	32.4 C deg	1019.2 hPa	0 C deg
1789921337	1007.8 hPa	31 C deg	1018.6 hPa	0 C deg
1789919507	1007.5 hPa	31.8 C deg	1018.2 hPa	0 C deg
1789916410	1007 hPa	32.6 C deg	1017.7 hPa	0 C deg
1789914580	1006.5 hPa	32.4 C deg	1017.3 hPa	0 C deg
1789912750	1005.8 hPa	31.4 C deg	1016.6 hPa	0 C deg
1789912561	1005.8 hPa	31.1 C deg	1016.6 hPa	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)