IK0PCJ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IK0PCJ-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1776658598	0 C deg	48.9 %	24 C deg
1776656777	0 C deg	48.9 %	24 C deg
1776654961	0 C deg	48.7 %	24 C deg
1776653145	0 C deg	48.6 %	24.1 C deg
1776651331	0 C deg	48.5 %	24.1 C deg
1776649523	0 C deg	48.5 %	24.1 C deg
1776647717	0 C deg	48.4 %	24.1 C deg
1776645883	0 C deg	48.1 %	24.2 C deg
1776644066	0 C deg	48.2 %	24.2 C deg
1776642252	0 C deg	48.1 %	24.3 C deg
1776640439	0 C deg	48.1 %	24.3 C deg
1776638625	0 C deg	48.1 %	24.3 C deg
1776636814	0 C deg	48 %	24.3 C deg
1776634989	0 C deg	47.9 %	24.3 C deg
1776631358	0 C deg	47.3 %	24.3 C deg
1776629547	0 C deg	46.9 %	24.4 C deg
1776627723	0 C deg	46.5 %	24.5 C deg
1776625910	0 C deg	46.1 %	24.6 C deg
1776624092	0 C deg	45.2 %	24.5 C deg
1776622279	0 C deg	44.9 %	24.6 C deg
1776620463	0 C deg	44.6 %	24.5 C deg
1776616830	0 C deg	43.8 %	24.6 C deg
1776615016	0 C deg	43.2 %	24.6 C deg
1776613199	0 C deg	41.6 %	24.8 C deg
1776611390	0 C deg	41.7 %	24.7 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)