XE1RCU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object XE1RCU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1788602032	13.95 Volt	10 Pkt	85 Pcnt
1788598432	13.95 Volt	10 Pkt	92 Pcnt
1788594832	13.95 Volt	10 Pkt	75 Pcnt
1788591232	13.95 Volt	10 Pkt	84 Pcnt
1788587632	13.95 Volt	20 Pkt	86 Pcnt
1788584032	13.95 Volt	10 Pkt	82 Pcnt
1788580432	13.95 Volt	10 Pkt	90 Pcnt
1788576832	13.95 Volt	10 Pkt	84 Pcnt
1788573232	13.95 Volt	10 Pkt	73 Pcnt
1788569633	13.95 Volt	10 Pkt	88 Pcnt
1788566033	13.95 Volt	10 Pkt	88 Pcnt
1788562433	13.95 Volt	10 Pkt	76 Pcnt
1788558833	13.95 Volt	10 Pkt	93 Pcnt
1788555233	13.95 Volt	10 Pkt	81 Pcnt
1788551633	13.95 Volt	10 Pkt	100 Pcnt
1788548033	13.95 Volt	10 Pkt	83 Pcnt
1788544433	13.95 Volt	10 Pkt	92 Pcnt
1788540833	13.95 Volt	10 Pkt	71 Pcnt
1788537234	13.95 Volt	10 Pkt	86 Pcnt
1788533634	13.95 Volt	10 Pkt	92 Pcnt
1788530034	13.95 Volt	10 Pkt	92 Pcnt
1788526434	13.95 Volt	10 Pkt	57 Pcnt
1788522834	13.95 Volt	10 Pkt	68 Pcnt
1788519234	13.95 Volt	10 Pkt	72 Pcnt
1788515634	13.95 Volt	10 Pkt	64 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)