DIGHTN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DIGHTN. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1776522460	14.25 Volt	210 Pkt	210 Pkt	70 Pcnt
1776521559	14.25 Volt	260 Pkt	260 Pkt	70 Pcnt
1776520657	14.25 Volt	240 Pkt	240 Pkt	70 Pcnt
1776519757	14.25 Volt	280 Pkt	280 Pkt	70 Pcnt
1776518856	14.25 Volt	340 Pkt	340 Pkt	76 Pcnt
1776517956	14.25 Volt	290 Pkt	290 Pkt	73 Pcnt
1776517055	14.25 Volt	260 Pkt	260 Pkt	76 Pcnt
1776516153	14.25 Volt	310 Pkt	310 Pkt	79 Pcnt
1776515253	14.25 Volt	270 Pkt	270 Pkt	79 Pcnt
1776514352	14.25 Volt	280 Pkt	280 Pkt	78 Pcnt
1776513451	14.25 Volt	290 Pkt	290 Pkt	78 Pcnt
1776512550	14.25 Volt	310 Pkt	310 Pkt	76 Pcnt
1776511650	14.25 Volt	240 Pkt	240 Pkt	76 Pcnt
1776510749	14.25 Volt	300 Pkt	300 Pkt	75 Pcnt
1776509848	14.25 Volt	210 Pkt	210 Pkt	73 Pcnt
1776508947	14.25 Volt	290 Pkt	290 Pkt	69 Pcnt
1776508046	14.25 Volt	290 Pkt	290 Pkt	62 Pcnt
1776507146	14.25 Volt	310 Pkt	310 Pkt	55 Pcnt
1776506244	14.25 Volt	190 Pkt	190 Pkt	43 Pcnt
1776505344	14.25 Volt	200 Pkt	200 Pkt	35 Pcnt
1776504443	14.25 Volt	100 Pkt	100 Pkt	22 Pcnt
1776503542	14.25 Volt	30 Pkt	30 Pkt	19 Pcnt
1776502641	14.25 Volt	60 Pkt	60 Pkt	15 Pcnt
1776501740	14.25 Volt	40 Pkt	40 Pkt	12 Pcnt
1776499938	14.25 Volt	0 Pkt	0 Pkt	5 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)