HG8PKU-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HG8PKU-14. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value4*	Value5*
1789981653	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789980838	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789979890	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789979072	12.5 Volt	13.2 Volt	5 Volt	29 Cels
1789978121	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789977306	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789976355	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789975539	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789974594	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789973773	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789972822	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789972007	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789971056	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789970240	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789969289	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789968477	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789967532	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789966708	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789965759	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789964941	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789963990	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789963175	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789962224	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789961419	12.4 Volt	13.2 Volt	5 Volt	29 Cels
1789960469	12.4 Volt	13.2 Volt	5 Volt	29 Cels

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)