ZL1SGC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ZL1SGC-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Charging/AC*	GPS+Sat*
1781862721	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781861821	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781860921	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781860016	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781859961	98 Percent	95 Charge/On/Off	48 Sats/On/Off
1781859156	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781858196	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781857296	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781857020	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781856121	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781855221	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781854320	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781854290	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781854290	98 Percent	95 Charge/On/Off	48 Sats/On/Off
1781853900	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781852100	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781851679	98 Percent	95 Charge/On/Off	2 Sats/On/Off
1781850750	98 Percent	95 Charge/On/Off	2 Sats/On/Off

*Used Equation Coefficients:

Battery: 0, 1, 0

Charging/AC: 0, 1, 0

GPS+Sat: 0, 1, 0

Current: 0, 10, -1280

A5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)