VK5ZX-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK5ZX-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx 1h*	DEC 1h*	Temp*
1761537059	14.1 Volt	32 Pkt	83 Pcnt	22 C
1761537058	14.1 Volt	32 Pkt	83 Pcnt	22 C
1761535258	14.1 Volt	32 Pkt	81 Pcnt	21 C
1761533459	14.1 Volt	30 Pkt	79 Pcnt	21 C
1761533459	14.1 Volt	30 Pkt	79 Pcnt	21 C
1761531659	14.1 Volt	31 Pkt	78 Pcnt	19.5 C
1761529859	14.1 Volt	30 Pkt	79 Pcnt	19 C
1761528065	14.1 Volt	32 Pkt	82 Pcnt	19 C
1761526259	14.1 Volt	39 Pkt	79 Pcnt	19 C
1761526259	14.1 Volt	39 Pkt	79 Pcnt	19 C
1761524459	14.1 Volt	40 Pkt	78 Pcnt	19 C
1761522660	14.1 Volt	39 Pkt	77 Pcnt	19 C
1761522659	14.1 Volt	39 Pkt	77 Pcnt	19 C
1761520859	14.1 Volt	46 Pkt	74 Pcnt	18 C
1761519060	14.1 Volt	44 Pkt	71 Pcnt	18.5 C
1761519059	14.1 Volt	44 Pkt	71 Pcnt	18.5 C
1761517259	14.1 Volt	43 Pkt	72 Pcnt	19 C
1761515460	14.1 Volt	43 Pkt	75 Pcnt	18.5 C
1761515459	14.1 Volt	43 Pkt	75 Pcnt	18.5 C
1761513659	14.1 Volt	36 Pkt	80 Pcnt	15.5 C
1761511860	14.1 Volt	39 Pkt	87 Pcnt	15 C
1761511859	14.1 Volt	39 Pkt	87 Pcnt	15 C
1761510059	14.1 Volt	46 Pkt	88 Pcnt	15 C
1761508260	14.1 Volt	41 Pkt	84 Pcnt	15 C
1761508259	14.1 Volt	41 Pkt	84 Pcnt	15 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx 1h: 0, 1, 0

DIG 1h: 0, 1, 0

DEC 1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)