KF8I Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KF8I. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1789962499	13.73 Volt	160 Pkt	89 Pcnt
1789960819	13.73 Volt	160 Pkt	88 Pcnt
1789959139	13.73 Volt	180 Pkt	83 Pcnt
1789957459	13.73 Volt	170 Pkt	75 Pcnt
1789955779	13.73 Volt	130 Pkt	66 Pcnt
1789954099	13.73 Volt	110 Pkt	58 Pcnt
1789952419	13.73 Volt	70 Pkt	47 Pcnt
1789950739	13.73 Volt	60 Pkt	42 Pcnt
1789949059	13.73 Volt	100 Pkt	58 Pcnt
1789947379	13.73 Volt	130 Pkt	76 Pcnt
1789945699	13.73 Volt	130 Pkt	79 Pcnt
1789944019	13.73 Volt	160 Pkt	86 Pcnt
1789942339	13.73 Volt	200 Pkt	93 Pcnt
1789940659	13.73 Volt	210 Pkt	95 Pcnt
1789938979	13.73 Volt	210 Pkt	98 Pcnt
1789937299	13.73 Volt	200 Pkt	98 Pcnt
1789935619	13.73 Volt	180 Pkt	92 Pcnt
1789933939	13.73 Volt	210 Pkt	91 Pcnt
1789932259	13.73 Volt	240 Pkt	94 Pcnt
1789930579	13.73 Volt	250 Pkt	94 Pcnt
1789928899	13.73 Volt	250 Pkt	91 Pcnt
1789927219	13.73 Volt	220 Pkt	91 Pcnt
1789925539	13.73 Volt	180 Pkt	93 Pcnt
1789923859	13.73 Volt	170 Pkt	94 Pcnt
1789922179	13.73 Volt	180 Pkt	96 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)