SR9WXW Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXW. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Visc10min*	Digi10min*	Vbatt*
1753638403	93 Pkt	0 Pkt	0 Pkt	12.96 V
1753637802	97 Pkt	1 Pkt	0 Pkt	12.96 V
1753637802	97 Pkt	1 Pkt	0 Pkt	12.96 V
1753636596	58 Pkt	0 Pkt	0 Pkt	13.1 V
1753636596	58 Pkt	0 Pkt	0 Pkt	13.1 V
1753635986	52 Pkt	0 Pkt	0 Pkt	13.18 V
1753635985	52 Pkt	0 Pkt	0 Pkt	13.18 V
1753635385	49 Pkt	0 Pkt	0 Pkt	13.12 V
1753634179	78 Pkt	0 Pkt	0 Pkt	13 V
1753634179	78 Pkt	0 Pkt	0 Pkt	13 V
1753633578	73 Pkt	0 Pkt	0 Pkt	13.02 V
1753632378	101 Pkt	0 Pkt	0 Pkt	13.02 V
1753631773	83 Pkt	0 Pkt	0 Pkt	13.02 V
1753631773	83 Pkt	0 Pkt	0 Pkt	13.02 V
1753631172	105 Pkt	1 Pkt	1 Pkt	13.02 V
1753631171	105 Pkt	1 Pkt	1 Pkt	13.02 V
1753630571	100 Pkt	0 Pkt	0 Pkt	13.14 V
1753630571	100 Pkt	0 Pkt	0 Pkt	13.14 V
1753629970	87 Pkt	0 Pkt	0 Pkt	13.84 V
1753629970	87 Pkt	0 Pkt	0 Pkt	13.84 V
1753629367	66 Pkt	0 Pkt	0 Pkt	14.08 V
1753629366	66 Pkt	0 Pkt	0 Pkt	14.08 V
1753628765	71 Pkt	0 Pkt	0 Pkt	14.08 V
1753628765	71 Pkt	0 Pkt	0 Pkt	14.08 V
1753628165	53 Pkt	0 Pkt	1 Pkt	14.16 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)