VK8ZM-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK8ZM-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Vin*	Eff1h*
1789953236	91.4 F	12.83 Volt	100 Pcnt
1789952876	90.5 F	12.75 Volt	100 Pcnt
1789952516	88.7 F	12.83 Volt	100 Pcnt
1789952156	87.8 F	12.83 Volt	100 Pcnt
1789951796	86.9 F	12.75 Volt	100 Pcnt
1789951436	86 F	12.83 Volt	100 Pcnt
1789951136	85.1 F	12.83 Volt	100 Pcnt
1789950289	83.3 F	12.75 Volt	100 Pcnt
1789949929	82.4 F	12.75 Volt	100 Pcnt
1789949629	82.4 F	12.83 Volt	100 Pcnt
1789948785	82.4 F	12.75 Volt	63 Pcnt
1789948425	81.5 F	12.75 Volt	63 Pcnt
1789948065	81.5 F	12.83 Volt	63 Pcnt
1789947708	80.6 F	12.83 Volt	63 Pcnt
1789947345	79.7 F	12.9 Volt	63 Pcnt
1789946985	79.7 F	12.98 Volt	77 Pcnt
1789946625	78.8 F	12.98 Volt	100 Pcnt
1789946265	77 F	12.9 Volt	100 Pcnt
1789945905	76.1 F	12.9 Volt	100 Pcnt
1789945545	75.2 F	12.83 Volt	100 Pcnt
1789945185	74.3 F	12.83 Volt	100 Pcnt
1789944825	73.4 F	12.75 Volt	100 Pcnt
1789944465	73.4 F	12.75 Volt	100 Pcnt
1789944105	72.5 F	12.75 Volt	100 Pcnt
1789943745	71.6 F	12.75 Volt	100 Pcnt

*Used Equation Coefficients:

Temp: 0, 0.9, -83.2

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)