DO0AB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO0AB-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1784678544	16.1 deg C	58.1 %	1023.9 hPa
1784677644	16 deg C	58.4 %	1024 hPa
1784676762	15.9 deg C	58.5 %	1024 hPa
1784675844	16 deg C	57.5 %	1024.1 hPa
1784674944	16.1 deg C	57.2 %	1024 hPa
1784674044	16.2 deg C	57.7 %	1024.1 hPa
1784673144	16.5 deg C	57.4 %	1024 hPa
1784672244	16.9 deg C	56.2 %	1023.9 hPa
1784671343	17.5 deg C	54.4 %	1023.7 hPa
1784670443	17.7 deg C	54.2 %	1023.5 hPa
1784669543	17.8 deg C	53.2 %	1023.5 hPa
1784668643	18.3 deg C	52.1 %	1023.4 hPa
1784667743	18.4 deg C	51.5 %	1023.3 hPa
1784666843	18.6 deg C	50.9 %	1023.2 hPa
1784665943	18.9 deg C	50.2 %	1023.2 hPa
1784665043	19 deg C	49.5 %	1023 hPa
1784664143	19.5 deg C	49.2 %	1022.7 hPa
1784663243	19.9 deg C	48.4 %	1022.4 hPa
1784662342	20.5 deg C	47.8 %	1022.2 hPa
1784661442	21.4 deg C	44.2 %	1021.7 hPa
1784660542	21.7 deg C	43.7 %	1021.4 hPa
1784659642	22 deg C	42.9 %	1021.2 hPa
1784658742	22.2 deg C	42.9 %	1021 hPa
1784657842	22.3 deg C	41.6 %	1021 hPa
1784656942	22.4 deg C	41.7 %	1020.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)