YC0TBU-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC0TBU-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humid*	Pressure*	SAT*	HDOP*
1781402523	35 C	49 %	1002 mBAR	7	0
1781402516	35 C	49 %	1002 mBAR	10	0
1781401661	35 C	50 %	1002 mBAR	10	0
1781399911	35 C	50 %	1002 mBAR	11	1
1781398158	35 C	50 %	1002 mBAR	11	0
1781396407	34 C	51 %	1002 mBAR	10	0
1781394655	34 C	51 %	1002 mBAR	10	1
1781392905	35 C	50 %	1002 mBAR	11	0
1781391162	35 C	50 %	1001 mBAR	12	0
1781389405	35 C	51 %	1001 mBAR	11	0
1781387656	34 C	51 %	1001 mBAR	10	0
1781385911	35 C	51 %	1001 mBAR	8	0
1781384155	35 C	51 %	1000 mBAR	10	0
1781382406	34 C	52 %	1001 mBAR	9	0
1781380656	34 C	53 %	1001 mBAR	10	0
1781378906	35 C	53 %	1001 mBAR	9	0
1781377155	35 C	51 %	1001 mBAR	9	0
1781375406	35 C	50 %	1002 mBAR	8	1
1781373655	35 C	50 %	1002 mBAR	9	0
1781371906	35 C	51 %	1002 mBAR	7	1
1781370156	35 C	50 %	1003 mBAR	9	0
1781368405	35 C	51 %	1003 mBAR	8	0
1781366655	35 C	50 %	1003 mBAR	10	0
1781364909	35 C	50 %	1003 mBAR	10	0
1781363155	35 C	49 %	1003 mBAR	10	0

*Used Equation Coefficients:

Temp: 0, 1, 0

Humid: 0, 1, 0

Pressure: 0, 1, 0

SAT: 0, 1, 0

HDOP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)