SR9NLI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NLI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Visc10min*	Vbatt*
1781358447	62 Pkt	0 Pkt	12.76 V
1781357830	85 Pkt	0 Pkt	12.76 V
1781357214	90 Pkt	0 Pkt	12.78 V
1781356599	88 Pkt	0 Pkt	12.78 V
1781355984	76 Pkt	0 Pkt	12.76 V
1781355368	83 Pkt	0 Pkt	12.74 V
1781354754	72 Pkt	0 Pkt	12.76 V
1781354139	96 Pkt	0 Pkt	12.78 V
1781353523	87 Pkt	0 Pkt	12.76 V
1781352908	85 Pkt	0 Pkt	12.76 V
1781352294	89 Pkt	0 Pkt	12.78 V
1781351679	99 Pkt	0 Pkt	12.78 V
1781351063	64 Pkt	0 Pkt	12.76 V
1781350438	108 Pkt	0 Pkt	12.78 V
1781349824	99 Pkt	0 Pkt	12.78 V
1781349209	109 Pkt	1 Pkt	12.76 V
1781348592	95 Pkt	0 Pkt	12.76 V
1781347361	97 Pkt	0 Pkt	12.74 V
1781346744	98 Pkt	1 Pkt	12.74 V
1781346128	90 Pkt	0 Pkt	12.72 V
1781345512	92 Pkt	0 Pkt	12.76 V
1781344280	97 Pkt	0 Pkt	12.72 V
1781343665	98 Pkt	0 Pkt	12.78 V
1781343050	89 Pkt	0 Pkt	12.78 V
1781342433	89 Pkt	0 Pkt	12.74 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)