DB0SON-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0SON-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773088547	13.95 Volt	210 Pkt	73 Pcnt
1773087947	13.95 Volt	210 Pkt	72 Pcnt
1773087347	13.88 Volt	210 Pkt	68 Pcnt
1773087347	13.88 Volt	210 Pkt	68 Pcnt
1773086747	13.95 Volt	210 Pkt	71 Pcnt
1773086147	13.95 Volt	230 Pkt	73 Pcnt
1773085547	13.95 Volt	240 Pkt	75 Pcnt
1773085547	13.95 Volt	240 Pkt	75 Pcnt
1773084947	13.95 Volt	250 Pkt	74 Pcnt
1773084347	13.88 Volt	270 Pkt	74 Pcnt
1773083747	13.95 Volt	270 Pkt	74 Pcnt
1773083747	13.95 Volt	270 Pkt	74 Pcnt
1773083147	13.88 Volt	270 Pkt	74 Pcnt
1773082547	13.95 Volt	240 Pkt	73 Pcnt
1773081947	13.88 Volt	240 Pkt	71 Pcnt
1773081947	13.88 Volt	240 Pkt	71 Pcnt
1773081347	13.88 Volt	240 Pkt	72 Pcnt
1773080747	13.88 Volt	230 Pkt	73 Pcnt
1773080147	13.88 Volt	220 Pkt	73 Pcnt
1773080147	13.88 Volt	220 Pkt	73 Pcnt
1773079547	13.88 Volt	230 Pkt	69 Pcnt
1773078947	13.88 Volt	240 Pkt	71 Pcnt
1773078347	13.88 Volt	230 Pkt	73 Pcnt
1773078347	13.88 Volt	230 Pkt	73 Pcnt
1773077747	13.95 Volt	230 Pkt	72 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

DiRxT: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)