IU1CYJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IU1CYJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	V_Bat*	V_Ext*
1774631109	891 Count	4.13 VDC	0.14 VDC
1774630806	890 Count	4.18 VDC	0.14 VDC
1774630503	889 Count	4.15 VDC	0.14 VDC
1774630201	888 Count	4.19 VDC	0.14 VDC
1774629898	887 Count	4.11 VDC	0.14 VDC
1774629595	886 Count	4.19 VDC	0.14 VDC
1774629292	885 Count	4.12 VDC	0.14 VDC
1774628989	884 Count	4.12 VDC	0.14 VDC
1774628687	883 Count	4.17 VDC	0.14 VDC
1774628384	882 Count	4.11 VDC	0.14 VDC
1774628081	881 Count	4.15 VDC	0.14 VDC
1774627778	880 Count	4.09 VDC	0.14 VDC
1774627475	879 Count	4.09 VDC	0.14 VDC
1774627172	878 Count	4.13 VDC	0.14 VDC
1774626870	877 Count	4.11 VDC	0.14 VDC
1774626567	876 Count	4.09 VDC	0.14 VDC
1774626264	875 Count	4.14 VDC	0.14 VDC
1774625961	874 Count	4.16 VDC	0.14 VDC
1774625658	873 Count	4.12 VDC	0.14 VDC
1774625356	872 Count	4.1 VDC	0.14 VDC
1774625053	871 Count	4.13 VDC	0.14 VDC
1774624750	870 Count	4.14 VDC	0.14 VDC
1774624447	869 Count	4.17 VDC	0.14 VDC
1774624144	868 Count	4.11 VDC	0.14 VDC
1774623841	867 Count	4.15 VDC	0.14 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)