SR9NCI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NCI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*
1772785516	74 Pkt	4 Pkt	0 Pkt
1772784910	61 Pkt	6 Pkt	0 Pkt
1772783696	60 Pkt	2 Pkt	0 Pkt
1772783093	60 Pkt	4 Pkt	0 Pkt
1772782488	63 Pkt	6 Pkt	0 Pkt
1772781878	66 Pkt	4 Pkt	0 Pkt
1772781273	55 Pkt	3 Pkt	0 Pkt
1772780669	38 Pkt	3 Pkt	0 Pkt
1772780093	39 Pkt	7 Pkt	0 Pkt
1772779454	57 Pkt	3 Pkt	0 Pkt
1772778851	61 Pkt	3 Pkt	0 Pkt
1772778247	52 Pkt	4 Pkt	0 Pkt
1772777641	58 Pkt	6 Pkt	0 Pkt
1772777032	64 Pkt	4 Pkt	0 Pkt
1772776426	64 Pkt	2 Pkt	0 Pkt
1772775823	61 Pkt	4 Pkt	0 Pkt
1772775218	62 Pkt	7 Pkt	0 Pkt
1772774606	71 Pkt	4 Pkt	1 Pkt
1772774002	63 Pkt	3 Pkt	0 Pkt
1772773398	63 Pkt	3 Pkt	0 Pkt
1772772794	47 Pkt	7 Pkt	0 Pkt
1772772183	55 Pkt	3 Pkt	0 Pkt
1772771580	51 Pkt	3 Pkt	0 Pkt
1772770976	66 Pkt	4 Pkt	0 Pkt
1772770371	44 Pkt	6 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

HostTx10m: 0, 1, 0

Tempre: 0, 0.25, -25

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)