SEELEY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SEELEY. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Eff*
1753943136	13.2 Volt	28.5 C	69 Pcnt
1753941036	13.2 Volt	28.5 C	69 Pcnt
1753938936	13.2 Volt	28.5 C	69 Pcnt
1753936836	12.98 Volt	28.5 C	69 Pcnt
1753934736	13.2 Volt	28.5 C	69 Pcnt
1753932636	13.2 Volt	28.5 C	69 Pcnt
1753930537	12.98 Volt	28 C	69 Pcnt
1753926337	12.98 Volt	27.5 C	69 Pcnt
1753924237	12.98 Volt	27.5 C	69 Pcnt
1753920037	13.2 Volt	27 C	69 Pcnt
1753913737	13.2 Volt	26.5 C	69 Pcnt
1753911637	13.2 Volt	26 C	69 Pcnt
1753909537	13.28 Volt	26 C	69 Pcnt
1753890638	13.2 Volt	26 C	69 Pcnt
1753888538	13.2 Volt	26 C	69 Pcnt
1753886438	13.2 Volt	26 C	69 Pcnt
1753884338	13.2 Volt	26.5 C	69 Pcnt
1753882258	13.2 Volt	26.5 C	69 Pcnt
1753880138	13.2 Volt	27 C	69 Pcnt
1753878038	13.2 Volt	27 C	69 Pcnt
1753875938	13.2 Volt	27 C	69 Pcnt
1753873839	13.13 Volt	27 C	69 Pcnt
1753871738	13.2 Volt	27.5 C	69 Pcnt
1753867538	13.2 Volt	27.5 C	69 Pcnt
1753865439	13.2 Volt	27.5 C	69 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -71

Dg1h: 0, 10, 0

Eff: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)