F5ZEE Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F5ZEE. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	PA Temp*	Value2*	Value3*	Value4*	Value5*
1765760343	12.37 deg.C	0	0	0	0
1765760045	12.53 deg.C	0	0	0	0
1765759745	12.53 deg.C	0	0	0	0
1765759444	12.53 deg.C	0	0	0	0
1765759144	12.53 deg.C	0	0	0	0
1765758845	12.53 deg.C	0	0	0	0
1765758545	12.53 deg.C	0	0	0	0
1765758244	12.53 deg.C	0	0	0	0
1765757944	12.53 deg.C	0	0	0	0
1765757644	12.53 deg.C	0	0	0	0
1765757343	12.53 deg.C	0	0	0	0
1765757045	12.53 deg.C	0	0	0	0
1765756744	12.69 deg.C	0	0	0	0
1765756445	12.53 deg.C	0	0	0	0
1765756144	12.53 deg.C	0	0	0	0
1765755867	12.69 deg.C	0	0	0	0
1765755546	12.69 deg.C	0	0	0	0
1765755243	12.69 deg.C	0	0	0	0
1765754945	12.69 deg.C	0	0	0	0
1765754643	12.69 deg.C	0	0	0	0
1765754345	12.69 deg.C	0	0	0	0
1765754043	12.69 deg.C	0	0	0	0
1765753745	12.69 deg.C	0	0	0	0
1765753445	12.69 deg.C	0	0	0	0
1765753144	12.69 deg.C	0	0	0	0

*Used Equation Coefficients:

PA Temp: 0, 0.16016, -40

Value2: 0, 0, 0

Value3: 0, 0, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)