EL-9A3AOT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EL-9A3AOT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Value1*	Value2*	Value3*	Value4*
1784575696	0 RX Erlang	20 TX Erlang	0 RXcount/10m	2 TXcount/10m
1784575096	0 RX Erlang	23 TX Erlang	0 RXcount/10m	3 TXcount/10m
1784574496	0 RX Erlang	40 TX Erlang	0 RXcount/10m	5 TXcount/10m
1784573896	0 RX Erlang	20 TX Erlang	0 RXcount/10m	2 TXcount/10m
1784573296	0 RX Erlang	20 TX Erlang	0 RXcount/10m	2 TXcount/10m
1784572696	1 RX Erlang	81 TX Erlang	1 RXcount/10m	16 TXcount/10m
1784144883	2 RX Erlang	45 TX Erlang	2 RXcount/10m	7 TXcount/10m
1784144283	0 RX Erlang	20 TX Erlang	0 RXcount/10m	2 TXcount/10m
1784143683	0 RX Erlang	156 TX Erlang	0 RXcount/10m	3 TXcount/10m
1784143083	0 RX Erlang	802 TX Erlang	0 RXcount/10m	19 TXcount/10m
1784142483	0 RX Erlang	890 TX Erlang	0 RXcount/10m	20 TXcount/10m
1784141883	0 RX Erlang	855 TX Erlang	0 RXcount/10m	21 TXcount/10m
1784141283	0 RX Erlang	262 TX Erlang	0 RXcount/10m	17 TXcount/10m
1784140683	11 RX Erlang	23 TX Erlang	2 RXcount/10m	3 TXcount/10m
1784140083	3 RX Erlang	97 TX Erlang	3 RXcount/10m	12 TXcount/10m

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)