OZ7KBR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OZ7KBR-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1772691340	14.03 Volt	500 Pkt	78 Pcnt
1772691041	14.03 Volt	500 Pkt	78 Pcnt
1772691040	14.03 Volt	500 Pkt	78 Pcnt
1772690740	14.03 Volt	480 Pkt	78 Pcnt
1772690441	14.03 Volt	470 Pkt	76 Pcnt
1772690440	14.03 Volt	470 Pkt	76 Pcnt
1772690140	14.03 Volt	470 Pkt	75 Pcnt
1772689841	14.03 Volt	440 Pkt	74 Pcnt
1772689840	14.03 Volt	440 Pkt	74 Pcnt
1772689540	14.03 Volt	420 Pkt	74 Pcnt
1772689241	14.03 Volt	410 Pkt	75 Pcnt
1772689240	14.03 Volt	410 Pkt	75 Pcnt
1772688940	14.03 Volt	390 Pkt	75 Pcnt
1772688642	14.03 Volt	360 Pkt	75 Pcnt
1772688640	14.03 Volt	360 Pkt	75 Pcnt
1772688340	14.03 Volt	330 Pkt	75 Pcnt
1772688042	14.03 Volt	310 Pkt	76 Pcnt
1772688040	14.03 Volt	310 Pkt	76 Pcnt
1772687740	14.03 Volt	300 Pkt	76 Pcnt
1772687441	14.03 Volt	290 Pkt	75 Pcnt
1772687440	14.03 Volt	290 Pkt	75 Pcnt
1772687140	14.03 Volt	280 Pkt	75 Pcnt
1772686841	14.03 Volt	280 Pkt	76 Pcnt
1772686840	14.03 Volt	280 Pkt	76 Pcnt
1772686540	14.03 Volt	270 Pkt	78 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)