TG5ALY-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TG5ALY-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1787627120	13.6 C deg	79.3 %	0 C deg
1787625293	13.7 C deg	79.7 %	0 C deg
1787623463	14 C deg	78.9 %	0 C deg
1787621629	14.7 C deg	77 %	0 C deg
1787619799	14.4 C deg	79.3 %	0 C deg
1787617970	14.9 C deg	77.1 %	0 C deg
1787616141	15.6 C deg	74.2 %	0 C deg
1787614310	16 C deg	73.1 %	0 C deg
1787612481	17 C deg	69.2 %	0 C deg
1787610652	18.6 C deg	63.3 %	0 C deg
1787608820	18.2 C deg	62.4 %	0 C deg
1787606989	19.5 C deg	60.6 %	0 C deg
1787605162	19.3 C deg	61 %	0 C deg
1787603328	19.6 C deg	61.9 %	0 C deg
1787601499	21 C deg	62.3 %	0 C deg
1787599670	18.9 C deg	64.6 %	0 C deg
1787597838	19.8 C deg	63.7 %	0 C deg
1787596009	19.3 C deg	66 %	0 C deg
1787594181	18.4 C deg	73.2 %	0 C deg
1787592352	19 C deg	71.5 %	0 C deg
1787590521	17.7 C deg	77.9 %	0 C deg
1787588692	17.8 C deg	74 %	0 C deg
1787586858	17.3 C deg	76 %	0 C deg
1787585027	17.1 C deg	75.9 %	0 C deg
1787583198	17.2 C deg	73.6 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)