IU1KBL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IU1KBL. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1765538246	13.73 Volt	10 Pkt	82 Pcnt	12.5 C
1765537946	13.73 Volt	10 Pkt	100 Pcnt	13 C
1765537646	13.73 Volt	10 Pkt	100 Pcnt	12.5 C
1765537346	13.73 Volt	0 Pkt	100 Pcnt	12 C
1765537046	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765536746	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765536446	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765536146	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765535546	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765535246	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765534946	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765534646	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765534346	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765534046	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765533746	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765533446	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765533164	13.73 Volt	10 Pkt	100 Pcnt	12 C
1765532546	13.73 Volt	10 Pkt	100 Pcnt	11.5 C
1765532246	13.73 Volt	10 Pkt	100 Pcnt	11.5 C
1765531946	13.73 Volt	10 Pkt	100 Pcnt	11.5 C
1765531646	13.73 Volt	10 Pkt	100 Pcnt	11.5 C
1765531346	13.73 Volt	10 Pkt	100 Pcnt	11.5 C
1765531046	13.73 Volt	10 Pkt	100 Pcnt	11 C
1765530746	13.73 Volt	10 Pkt	100 Pcnt	11 C
1765530463	13.73 Volt	10 Pkt	100 Pcnt	11 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)