OE5XDO-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE5XDO-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP-PA*	LM75*	Pv*	Pr*
1780536067	22 Grad	13 Grad	18 W	1 W
1780535678	22 Grad	13 Grad	18 W	1 W
1780535288	22 Grad	13 Grad	18 W	1 W
1780534899	24 Grad	13 Grad	18 W	1 W
1780534510	22 Grad	13 Grad	18.3 W	1 W
1780534120	22 Grad	13 Grad	18.3 W	1 W
1780533730	22 Grad	13 Grad	18.3 W	1 W
1780533341	22 Grad	13 Grad	18.3 W	1 W
1780532951	22 Grad	13 Grad	18 W	1 W
1780532562	22 Grad	13 Grad	18 W	1 W
1780532173	22 Grad	14 Grad	18 W	1 W
1780531394	24 Grad	13 Grad	18 W	1 W
1780531004	22 Grad	13 Grad	18.4 W	1 W
1780530614	22 Grad	13 Grad	18.4 W	1 W
1780530225	22 Grad	14 Grad	18.4 W	1 W
1780529835	22 Grad	14 Grad	18.4 W	1 W
1780529446	23 Grad	13 Grad	18.4 W	1 W
1780528667	23 Grad	14 Grad	18 W	1 W
1780528279	23 Grad	14 Grad	18 W	1 W
1780527888	24 Grad	14 Grad	18 W	1 W
1780527498	22 Grad	14 Grad	18.1 W	1 W
1780527109	22 Grad	14 Grad	18.1 W	1 W
1780526719	22 Grad	14 Grad	18.1 W	1 W
1780525940	23 Grad	14 Grad	18.1 W	1 W
1780525551	22 Grad	14 Grad	18 W	1 W

*Used Equation Coefficients:

TEMP-PA: 0, 1, -150

DACFAN: 0, 1, 0

LM75: 0, 1, -150

Pv: 0, 0.1, 0

Pr: 0, 0.1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)