DC1MBB-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC1MBB-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1761588438	12.7 deg C	60.3 %	996.7 hPa
1761588115	12.7 deg C	60.3 %	996.6 hPa
1761587218	12.7 deg C	60.3 %	996.5 hPa
1761586318	12.7 deg C	60.4 %	996.2 hPa
1761585415	12.7 deg C	60.5 %	995.8 hPa
1761584513	12.7 deg C	60.5 %	995.2 hPa
1761583608	12.7 deg C	60.5 %	995.2 hPa
1761582707	12.8 deg C	60.5 %	995.1 hPa
1761581809	12.8 deg C	60.5 %	994.7 hPa
1761580910	12.8 deg C	60.4 %	994.5 hPa
1761580007	12.8 deg C	60.4 %	994.4 hPa
1761579104	12.8 deg C	60.4 %	994.5 hPa
1761578209	12.8 deg C	60.4 %	994.3 hPa
1761577310	12.8 deg C	60.5 %	993.7 hPa
1761576403	12.8 deg C	60.5 %	993.9 hPa
1761576079	12.8 deg C	60.6 %	993.8 hPa
1761575175	12.8 deg C	60.7 %	993.7 hPa
1761574276	12.9 deg C	60.7 %	993.6 hPa
1761572484	12.9 deg C	60.8 %	993.4 hPa
1761571581	12.9 deg C	60.7 %	993.3 hPa
1761570683	12.9 deg C	60.7 %	993 hPa
1761568882	12.9 deg C	60.6 %	993 hPa
1761567080	12.9 deg C	60.2 %	993.3 hPa
1761566178	12.9 deg C	60 %	993.1 hPa
1761565278	12.9 deg C	60.1 %	993.2 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)