DB0II-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0II-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1785318994	32.1 deg C	40.9 %	612.8 hPa
1785318094	33.6 deg C	39.8 %	619.9 hPa
1785317194	31.3 deg C	42.1 %	608.1 hPa
1785316294	32.8 deg C	40.7 %	615.8 hPa
1785315409	31.3 deg C	42.6 %	608 hPa
1785314494	29.2 deg C	46.1 %	596.9 hPa
1785313633	28.4 deg C	47.2 %	591.5 hPa
1785312694	27.7 deg C	49 %	585.9 hPa
1785311794	28.5 deg C	48.4 %	591.3 hPa
1785310893	27 deg C	50.3 %	581.3 hPa
1785309993	27 deg C	50.4 %	580.6 hPa
1785309093	25.4 deg C	53.4 %	568.9 hPa
1785308193	24.8 deg C	54 %	564.3 hPa
1785307293	24.4 deg C	54.9 %	561.3 hPa
1785306393	24 deg C	55.6 %	557.7 hPa
1785305493	23.3 deg C	57.4 %	552.6 hPa
1785304593	23 deg C	58.1 %	549.8 hPa
1785303692	21.8 deg C	60.8 %	540.2 hPa
1785302792	21.2 deg C	62.6 %	536.7 hPa
1785301892	20.6 deg C	64.1 %	532.6 hPa
1785300992	20 deg C	66.6 %	530.5 hPa
1785300092	19.6 deg C	68.1 %	529.1 hPa
1785299192	19.3 deg C	69.4 %	528.3 hPa
1785298292	19.4 deg C	69 %	529.6 hPa
1785297392	19.7 deg C	68.4 %	531.8 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)