SR9NIS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NIS. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Vbatt*
1789963411	6 Pkt	3 Pkt	13.5 V
1789960863	5 Pkt	9 Pkt	13.52 V
1789958948	8 Pkt	2 Pkt	13.52 V
1789957671	7 Pkt	4 Pkt	13.5 V
1789957182	5 Pkt	2 Pkt	13.5 V
1789955115	8 Pkt	2 Pkt	13.48 V
1789951936	8 Pkt	5 Pkt	13.5 V
1789951294	8 Pkt	2 Pkt	13.46 V
1789950018	5 Pkt	4 Pkt	13.5 V
1789943636	6 Pkt	2 Pkt	13.48 V
1789942369	7 Pkt	2 Pkt	13.48 V
1789941091	7 Pkt	9 Pkt	13.5 V
1789938536	15 Pkt	4 Pkt	13.48 V
1789934710	8 Pkt	2 Pkt	13.48 V
1789934081	13 Pkt	4 Pkt	13.46 V
1789933432	9 Pkt	4 Pkt	13.5 V
1789930886	20 Pkt	16 Pkt	13.46 V
1789930232	13 Pkt	4 Pkt	13.46 V
1789929594	11 Pkt	2 Pkt	13.5 V
1789928316	17 Pkt	4 Pkt	13.5 V
1789927049	11 Pkt	4 Pkt	13.48 V
1789925771	14 Pkt	4 Pkt	13.48 V
1789925134	12 Pkt	5 Pkt	13.48 V
1789924491	15 Pkt	2 Pkt	13.46 V
1789923853	12 Pkt	4 Pkt	13.52 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)