DJ7ACM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DJ7ACM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1788584016	25.7 deg C	52 %	1019.1 hPa
1788583116	25.7 deg C	52 %	1019 hPa
1788582216	25.7 deg C	52 %	1018.6 hPa
1788581316	25.7 deg C	52 %	1018.6 hPa
1788580416	25.7 deg C	52 %	1018.3 hPa
1788579516	25.7 deg C	52 %	1018.3 hPa
1788578616	25.7 deg C	52 %	1018.1 hPa
1788577716	25.6 deg C	52 %	1018.5 hPa
1788576816	25.6 deg C	52 %	1018.7 hPa
1788575915	25.5 deg C	51.3 %	1018.5 hPa
1788575015	25.3 deg C	51.4 %	1018.7 hPa
1788574115	25.2 deg C	51.2 %	1018.4 hPa
1788573215	25.1 deg C	49.9 %	1018.3 hPa
1788572315	25.1 deg C	49.6 %	1017.9 hPa
1788571985	25.1 deg C	49.5 %	1018.1 hPa
1788571085	25.2 deg C	49.2 %	1017.9 hPa
1788570185	25.2 deg C	49 %	1017.3 hPa
1788569285	25.2 deg C	48.8 %	1018.1 hPa
1788568385	25.2 deg C	48.6 %	1017.1 hPa
1788567484	25.2 deg C	48.3 %	1016.6 hPa
1788566584	25.2 deg C	48.1 %	1016.8 hPa
1788565684	25.1 deg C	47.7 %	1016.2 hPa
1788564784	25.1 deg C	47.3 %	1016.1 hPa
1788563884	25.1 deg C	47.1 %	1016.2 hPa
1788562984	25.1 deg C	46.9 %	1016.1 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)