KJ7EBU Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KJ7EBU. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1776696661	12.54 Volts	1010.8 Deg.F
1776689745	12.39 Volts	1002.01 Deg.F
1776684253	12.42 Volts	1006.41 Deg.F
1776683657	12.42 Volts	1006.41 Deg.F
1776683180	12.45 Volts	1006.41 Deg.F
1776682106	12.42 Volts	1006.41 Deg.F
1776681270	12.45 Volts	1006.41 Deg.F
1776680196	12.45 Volts	1007.29 Deg.F
1776679852	12.48 Volts	1007.29 Deg.F
1776679746	12.45 Volts	1007.29 Deg.F
1776679600	12.48 Volts	1007.29 Deg.F
1776679480	12.45 Volts	1007.29 Deg.F
1776679361	12.45 Volts	1007.29 Deg.F
1776678287	12.48 Volts	1008.17 Deg.F
1776661574	12.72 Volts	1014.32 Deg.F
1776612681	12.66 Volts	1014.32 Deg.F
1776611009	12.63 Volts	1010.8 Deg.F
1776606601	12.39 Volts	997.62 Deg.F
1776606539	12.42 Volts	997.62 Deg.F
1776606425	12.39 Volts	997.62 Deg.F
1776606356	12.39 Volts	997.62 Deg.F
1776606237	12.42 Volts	997.62 Deg.F
1776606117	12.39 Volts	997.62 Deg.F
1776605760	12.39 Volts	997.62 Deg.F
1776605640	12.36 Volts	997.62 Deg.F

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.879, 459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)