MB7UNE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UNE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Vin*	Dg1h*	Eff1h*
1789968404	25 C	13.88 Volt	10 Pkt	73
1789967804	25 C	13.88 Volt	10 Pkt	72
1789967205	25 C	13.88 Volt	20 Pkt	72
1789967204	25 C	13.88 Volt	20 Pkt	72
1789966604	25 C	13.88 Volt	20 Pkt	74
1789966004	25 C	13.88 Volt	10 Pkt	78
1789965405	25 C	13.88 Volt	10 Pkt	78
1789965404	25 C	13.88 Volt	10 Pkt	78
1789964804	25.5 C	13.88 Volt	20 Pkt	78
1789964204	25.5 C	13.88 Volt	20 Pkt	78
1789963605	25.5 C	13.88 Volt	10 Pkt	78
1789963604	25.5 C	13.88 Volt	10 Pkt	78
1789963004	25.5 C	13.88 Volt	10 Pkt	77
1789962404	25.5 C	13.88 Volt	10 Pkt	75
1789961805	25.5 C	13.88 Volt	10 Pkt	77
1789961804	25.5 C	13.88 Volt	10 Pkt	77
1789961204	25.5 C	13.88 Volt	20 Pkt	77
1789960604	25.5 C	13.88 Volt	20 Pkt	80
1789960008	25.5 C	13.88 Volt	20 Pkt	83
1789960004	25.5 C	13.88 Volt	20 Pkt	83
1789959404	25.5 C	13.88 Volt	20 Pkt	86
1789958804	25.5 C	13.88 Volt	10 Pkt	84
1789958205	25.5 C	13.88 Volt	10 Pkt	84
1789958204	25.5 C	13.88 Volt	10 Pkt	84
1789957604	25.5 C	13.88 Volt	10 Pkt	84

*Used Equation Coefficients:

Temp: 0, 0.5, -64

Vin: 0, 0.075, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)