N0NHJ-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N0NHJ-7. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1778681470	13.51 Volt	20 Pkt	78 Pcnt
1778681169	13.67 Volt	10 Pkt	79 Pcnt
1778680869	13.59 Volt	20 Pkt	84 Pcnt
1778680569	13.59 Volt	10 Pkt	81 Pcnt
1778680269	13.59 Volt	20 Pkt	80 Pcnt
1778679969	13.67 Volt	10 Pkt	81 Pcnt
1778679669	13.67 Volt	20 Pkt	77 Pcnt
1778679369	13.67 Volt	10 Pkt	77 Pcnt
1778679069	13.67 Volt	10 Pkt	80 Pcnt
1778678769	13.67 Volt	10 Pkt	81 Pcnt
1778678469	13.67 Volt	10 Pkt	78 Pcnt
1778678169	13.67 Volt	10 Pkt	75 Pcnt
1778677869	13.67 Volt	10 Pkt	78 Pcnt
1778677569	13.67 Volt	10 Pkt	72 Pcnt
1778677269	13.67 Volt	10 Pkt	76 Pcnt
1778676969	13.67 Volt	10 Pkt	76 Pcnt
1778676669	13.67 Volt	10 Pkt	76 Pcnt
1778676369	13.67 Volt	10 Pkt	81 Pcnt
1778676069	13.67 Volt	10 Pkt	84 Pcnt
1778675769	13.67 Volt	10 Pkt	82 Pcnt
1778675469	13.59 Volt	10 Pkt	80 Pcnt
1778675169	13.67 Volt	10 Pkt	83 Pcnt
1778674869	13.67 Volt	10 Pkt	78 Pcnt
1778674569	13.67 Volt	10 Pkt	75 Pcnt
1778674269	13.67 Volt	10 Pkt	75 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)