VK2HFG-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2HFG-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	CPU*	Tx*
1784708806	12.5 Volts	45 DegC	6 pkts
1784705206	12.6 Volts	49 DegC	6 pkts
1784701606	13.1 Volts	52 DegC	9 pkts
1784698006	13.8 Volts	53 DegC	18 pkts
1784694406	14 Volts	53 DegC	24 pkts
1784690807	13.8 Volts	51 DegC	25 pkts
1784687207	13.8 Volts	50 DegC	36 pkts
1784683606	13.9 Volts	46 DegC	34 pkts
1784680007	13.1 Volts	42 DegC	13 pkts
1784676406	13.7 Volts	41 DegC	15 pkts
1784672807	13 Volts	39 DegC	6 pkts
1784669207	12.2 Volts	39 DegC	6 pkts
1784665607	12.3 Volts	39 DegC	6 pkts
1784662007	12.2 Volts	38 DegC	6 pkts
1784658407	12.2 Volts	39 DegC	6 pkts
1784654806	12.3 Volts	38 DegC	18 pkts
1784651206	12.3 Volts	38 DegC	13 pkts
1784647607	12.3 Volts	39 DegC	6 pkts
1784644006	12.4 Volts	39 DegC	6 pkts
1784640406	12.4 Volts	39 DegC	6 pkts
1784636806	12.4 Volts	40 DegC	6 pkts
1784633206	12.3 Volts	40 DegC	6 pkts
1784629606	12.4 Volts	41 DegC	6 pkts
1784626006	12.5 Volts	41 DegC	6 pkts
1784622406	12.5 Volts	44 DegC	6 pkts

*Used Equation Coefficients:

Battery: 0, 0.1, 0

CPU: 0, 1, 0

Tx: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)