VK2XSE-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2XSE-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1765569622	12.45 Volt	20 Pkt	62 Pcnt
1765569322	12.53 Volt	20 Pkt	59 Pcnt
1765569022	12.53 Volt	20 Pkt	59 Pcnt
1765568722	12.53 Volt	20 Pkt	59 Pcnt
1765568422	12.53 Volt	20 Pkt	45 Pcnt
1765568122	12.53 Volt	20 Pkt	41 Pcnt
1765567824	12.45 Volt	20 Pkt	42 Pcnt
1765567522	12.53 Volt	20 Pkt	41 Pcnt
1765567222	12.53 Volt	20 Pkt	39 Pcnt
1765566922	12.53 Volt	30 Pkt	41 Pcnt
1765566622	12.53 Volt	30 Pkt	41 Pcnt
1765566322	12.53 Volt	30 Pkt	43 Pcnt
1765566024	12.45 Volt	30 Pkt	44 Pcnt
1765566022	12.45 Volt	30 Pkt	44 Pcnt
1765565734	12.53 Volt	30 Pkt	46 Pcnt
1765565422	12.53 Volt	30 Pkt	44 Pcnt
1765565122	12.45 Volt	30 Pkt	48 Pcnt
1765564824	12.53 Volt	40 Pkt	50 Pcnt
1765564822	12.53 Volt	40 Pkt	50 Pcnt
1765564522	12.53 Volt	40 Pkt	53 Pcnt
1765564224	12.45 Volt	30 Pkt	56 Pcnt
1765564222	12.45 Volt	30 Pkt	56 Pcnt
1765563922	12.53 Volt	30 Pkt	56 Pcnt
1765563622	12.53 Volt	40 Pkt	56 Pcnt
1765563322	12.53 Volt	30 Pkt	59 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)