BX6AM-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1761628041	41.5 C	10 p	17 p	20 p	5 p
1761626841	41.3 C	6 p	14 p	16 p	4 p
1761625641	41.9 C	7 p	9 p	10 p	3 p
1761624442	41.8 C	2 p	4 p	4 p	84 p
1761623242	41.1 C	2 p	3 p	3 p	84 p
1761622041	39.9 C	1 p	1 p	1 p	84 p
1761620842	30.6 C	1 p	3 p	104 p	84 p
1761619649	40.5 C	1 p	3 p	104 p	84 p
1761618449	40.2 C	2 p	4 p	103 p	84 p
1761617248	40.1 C	3 p	8 p	101 p	84 p
1761616049	40.2 C	3 p	8 p	101 p	84 p
1761614850	40.2 C	3 p	8 p	100 p	83 p
1761613649	39.7 C	3 p	5 p	97 p	80 p
1761612449	40.3 C	2 p	7 p	94 p	80 p
1761611249	40.2 C	5 p	7 p	92 p	79 p
1761610050	38.9 C	5 p	7 p	92 p	79 p
1761607659	38.5 C	1 p	3 p	86 p	73 p
1761606449	38.8 C	1 p	3 p	85 p	72 p
1761605249	38.5 C	2 p	4 p	84 p	71 p
1761604049	38.6 C	2 p	4 p	84 p	71 p
1761602849	38.9 C	1 p	5 p	83 p	70 p
1761601649	38.6 C	3 p	10 p	82 p	69 p
1761600450	39.5 C	3 p	10 p	82 p	69 p
1761599249	40.1 C	5 p	10 p	79 p	66 p
1761598049	40.2 C	5 p	8 p	77 p	64 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)