HS2EOY-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS2EOY-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Eff*
1772945024	14.06 Volt	0 Pcnt	62 Pcnt
1772944423	14.06 Volt	0 Pcnt	62 Pcnt
1772943823	14.06 Volt	0 Pcnt	62 Pcnt
1772943222	14.06 Volt	0 Pcnt	62 Pcnt
1772942621	14.06 Volt	0 Pcnt	62 Pcnt
1772942021	14.06 Volt	0 Pcnt	62 Pcnt
1772941420	14.06 Volt	100 Pcnt	62 Pcnt
1772940820	14.06 Volt	100 Pcnt	62 Pcnt
1772940219	14.06 Volt	100 Pcnt	62 Pcnt
1772939619	14.06 Volt	100 Pcnt	62 Pcnt
1772939018	14.06 Volt	100 Pcnt	62 Pcnt
1772938417	14.06 Volt	100 Pcnt	62 Pcnt
1772937817	14.06 Volt	100 Pcnt	62 Pcnt
1772937216	14.06 Volt	100 Pcnt	62 Pcnt
1772936616	14.06 Volt	100 Pcnt	62 Pcnt
1772936015	14.06 Volt	100 Pcnt	62 Pcnt
1772935415	14.06 Volt	100 Pcnt	62 Pcnt
1772934814	14.06 Volt	100 Pcnt	62 Pcnt
1772934213	14.06 Volt	100 Pcnt	62 Pcnt
1772933613	14.06 Volt	100 Pcnt	62 Pcnt
1772933012	14.06 Volt	100 Pcnt	62 Pcnt
1772932412	14.06 Volt	100 Pcnt	62 Pcnt
1772931211	14.06 Volt	100 Pcnt	62 Pcnt
1772930610	14.06 Volt	100 Pcnt	62 Pcnt
1772929409	14.06 Volt	100 Pcnt	62 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Eff: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)