N6LED-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N6LED-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RFIn*	RFiGate*	Temp*
1753688396	102 Pkts	102 Pkts	19 C
1753684792	90 Pkts	90 Pkts	19 C
1753681192	122 Pkts	122 Pkts	20 C
1753677611	147 Pkts	147 Pkts	20 C
1753673992	90 Pkts	90 Pkts	20 C
1753670392	31 Pkts	31 Pkts	20 C
1753666791	70 Pkts	70 Pkts	20 C
1753663192	95 Pkts	95 Pkts	20 C
1753659591	85 Pkts	85 Pkts	20 C
1753652392	214 Pkts	214 Pkts	20 C
1753645191	139 Pkts	139 Pkts	20 C
1753641592	156 Pkts	26 Pkts	19 C
1753627192	61 Pkts	61 Pkts	17 C
1753623592	69 Pkts	68 Pkts	19 C
1753619992	104 Pkts	104 Pkts	19 C
1753616392	144 Pkts	144 Pkts	19 C
1753612792	107 Pkts	106 Pkts	19 C
1753609193	109 Pkts	109 Pkts	20 C
1753605593	127 Pkts	127 Pkts	19 C
1753601992	134 Pkts	134 Pkts	19 C
1753598418	148 Pkts	146 Pkts	20 C
1753594792	122 Pkts	122 Pkts	20 C
1753591192	111 Pkts	110 Pkts	20 C
1753587592	79 Pkts	76 Pkts	20 C
1753583992	30 Pkts	30 Pkts	20 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)