DO1GER-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO1GER-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RX Pakete*	Value2*	Value3*	Value4*	Value5*
1776660684	28 Anzahl/10Min	0	0	0	0
1776660084	34 Anzahl/10Min	0	0	0	0
1776659484	45 Anzahl/10Min	0	0	0	0
1776658884	37 Anzahl/10Min	0	0	0	0
1776658284	37 Anzahl/10Min	0	0	0	0
1776657684	56 Anzahl/10Min	0	0	0	0
1776657084	46 Anzahl/10Min	0	0	0	0
1776656484	41 Anzahl/10Min	0	0	0	0
1776655884	30 Anzahl/10Min	0	0	0	0
1776655284	41 Anzahl/10Min	0	0	0	0
1776654684	32 Anzahl/10Min	0	0	0	0
1776654084	46 Anzahl/10Min	0	0	0	0
1776653484	40 Anzahl/10Min	0	0	0	0
1776652884	34 Anzahl/10Min	0	0	0	0
1776652284	43 Anzahl/10Min	0	0	0	0
1776651684	45 Anzahl/10Min	0	0	0	0
1776651084	30 Anzahl/10Min	0	0	0	0
1776650484	33 Anzahl/10Min	0	0	0	0
1776649884	38 Anzahl/10Min	0	0	0	0
1776649284	43 Anzahl/10Min	0	0	0	0
1776648684	37 Anzahl/10Min	0	0	0	0
1776648084	41 Anzahl/10Min	0	0	0	0
1776647484	39 Anzahl/10Min	0	0	0	0
1776646884	40 Anzahl/10Min	0	0	0	0
1776646284	46 Anzahl/10Min	0	0	0	0

*Used Equation Coefficients:

RX Pakete: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)