YC0TBU-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC0TBU-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	PRES*	SAT*	HDOP*
1773263682	35 °C	45 %	1005 mBar	8	1
1773262482	35 °C	45 %	1005 mBar	8	1
1773261282	36 °C	45 %	1005 mBar	5	1
1773260082	36 °C	45 %	1005 mBar	10	1
1773258882	36 °C	45 %	1005 mBar	8	1
1773257682	36 °C	45 %	1005 mBar	10	0
1773256465	36 °C	45 %	1005 mBar	11	0
1773255265	36 °C	44 %	1005 mBar	7	2
1773254065	36 °C	44 %	1005 mBar	9	0
1773252865	36 °C	44 %	1006 mBar	8	1
1773251664	35 °C	43 %	1006 mBar	8	1
1773250464	36 °C	44 %	1006 mBar	10	0
1773249269	36 °C	44 %	1006 mBar	10	0
1773248065	36 °C	44 %	1006 mBar	8	0
1773246864	36 °C	45 %	1007 mBar	7	1
1773245664	36 °C	45 %	1007 mBar	6	1
1773244466	36 °C	45 %	1007 mBar	7	1
1773243265	36 °C	46 %	1007 mBar	7	0
1773242648	36 °C	46 %	1007 mBar	7	1
1773241448	36 °C	46 %	1007 mBar	8	0
1773240249	36 °C	46 %	1007 mBar	8	0
1773239048	36 °C	46 %	1007 mBar	8	0
1773237848	36 °C	46 %	1007 mBar	6	1
1773236648	36 °C	45 %	1007 mBar	6	1
1773235448	36 °C	45 %	1007 mBar	9	1

*Used Equation Coefficients:

TEMP: 0, 1, 0

HUM: 0, 1, 0

PRES: 0, 1, 0

SAT: 0, 1, 0

HDOP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)