HS2AC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS2AC-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1787549395	26 Pkt	-43 dBm	13.39 V
1787548771	34 Pkt	-43 dBm	13.64 V
1787548145	25 Pkt	-42 dBm	12.51 V
1787547520	17 Pkt	-43 dBm	12.2 V
1787546895	20 Pkt	-43 dBm	12.47 V
1787546270	27 Pkt	-42 dBm	13.49 V
1787545644	22 Pkt	-43 dBm	13.49 V
1787545018	22 Pkt	-43 dBm	13.6 V
1787544393	20 Pkt	-43 dBm	12.2 V
1787543768	17 Pkt	-43 dBm	12.26 V
1787543142	20 Pkt	-43 dBm	13.31 V
1787542518	3 Pkt	-43 dBm	13.29 V
1787542326	14 Pkt	-43 dBm	13.45 V
1787541701	19 Pkt	-42 dBm	13.43 V
1787541076	20 Pkt	-43 dBm	13.23 V
1787540451	17 Pkt	-43 dBm	13.31 V
1787539826	17 Pkt	-43 dBm	13.29 V
1787539201	18 Pkt	-43 dBm	13.06 V
1787538576	27 Pkt	-43 dBm	13.95 V
1787537951	20 Pkt	-42 dBm	14.05 V
1787537325	18 Pkt	-42 dBm	12.84 V
1787536700	22 Pkt	-42 dBm	14.07 V
1787536074	17 Pkt	-42 dBm	13.97 V
1787535450	26 Pkt	-42 dBm	13.86 V
1787534824	50 Pkt	-42 dBm	13.9 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)