BM6HFL-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HFL-6. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1761526201	38.6 C	1 p	3 p	59 p
1761521401	38.5 C	0 p	2 p	58 p
1761519001	38 C	1 p	2 p	58 p
1761517801	37.7 C	0 p	2 p	58 p
1761515407	38.9 C	1 p	1 p	58 p
1761514201	39.1 C	0 p	1 p	58 p
1761513002	39 C	0 p	1 p	58 p
1761511801	39.2 C	1 p	2 p	59 p
1761510601	39.5 C	0 p	2 p	59 p
1761509402	40 C	1 p	2 p	59 p
1761508201	39.5 C	1 p	2 p	59 p
1761507001	39.2 C	0 p	2 p	59 p
1761505801	38.4 C	1 p	2 p	59 p
1761504601	39 C	1 p	2 p	59 p
1761503401	38.9 C	0 p	2 p	59 p
1761502201	39.2 C	1 p	2 p	59 p
1761499801	39.2 C	0 p	2 p	59 p
1761498601	38 C	1 p	2 p	59 p
1761497401	37.9 C	1 p	2 p	59 p
1761496201	38.5 C	0 p	2 p	59 p
1761495001	38 C	1 p	2 p	59 p
1761493802	37.9 C	1 p	2 p	59 p
1761491401	38.5 C	1 p	2 p	59 p
1761490202	38.8 C	1 p	2 p	59 p
1761487801	38.4 C	1 p	2 p	59 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)